How to Read a PVC Resin Bag: Standards, Grades and Markings
A practical guide to PVC resin packaging: GB/T 5761-2018 vs enterprise standards, why S-700 and SG-5 are different systems, and net weight tolerances.
An order for PVC resin names one thing. The bags that arrive often name something slightly different: a different grade name, a different standard number, a net weight written three different ways. For a buyer receiving a first shipment from a new supplier, this is where most of the uncertainty sits.
This article sets out what is actually printed on a PVC resin bag, what each line means, and which differences are routine versus which ones deserve a question before the delivery note is signed.
Everything below is industry-standard marking practice. The photographs show real bags from stock, for comparison with what a buyer receives.
1. The standard line: GB/T 5761-2018 is not the only valid answer
The single most common source of confusion. Buyers often assume a bag without "GB/T 5761" on it is substandard. That assumption is incorrect.
| Marking | What it is | Is it acceptable? |
|---|---|---|
GB/T 5761-2018 | National standard for suspension PVC resin, current version | Yes, the baseline |
GB/T 5761-2006 | The previous national standard version | Yes, if the resin was produced under it |
Q/SH3160.77-2016 / -2019 | Enterprise standard (企标), used by large producers whose internal specs are tighter than the national baseline | Yes, often stricter |
Q/TWPVC 001-2017 | Enterprise standard for a specialty grade (e.g. matte/消光 resin) | Yes, no national standard exists for that grade |

The practical rule: a standard line tells which specification the batch was tested against. It says nothing about how good the resin is. What matters is that the standard on the bag matches the standard on the COA that was sent. If the bag says Q/SH3160.77-2019 and the COA says GB/T 5761-2018, the discrepancy should be queried. One of the two documents is describing a different batch.
2. The grade line: S-700 and SG-5 are two naming systems, not two products
This trips up experienced buyers too. Two numbering conventions coexist in the Chinese PVC market:
| System | Example | Who uses it | Maps to |
|---|---|---|---|
| National grade code | SG-5 | Most producers; the GB/T 5761 convention | The "5" indicates the K-value / degree of polymerization band |
| Producer model number | S-700, S-1000, S-1300 | Several large state-owned producers | An internal model line. The number is not the SG grade |
The trap: S-700 and SG-7 are not the same thing. The number in an S-series model is a producer-internal designator. Two different producers can both sell "S-700" and the resins may differ.

How to avoid the mismatch: when an offer quotes S-1000, the buyer should request three things in writing — the equivalent SG range, the K-value, and the application the resin is intended for. A supplier unable to answer is reselling without understanding the product.
3. Net weight: three ways of writing the same 25 kg
Legitimate bags carry all of these:
| Printed as | Meaning |
|---|---|
净含量: 25kg | Nominal 25 kg |
净含量: 25.0kg ± 0.2kg | 25 kg with a stated filling tolerance (the honest version) |
NET WT: 25kg | English equivalent |
净重: 1000KG | This is a jumbo bag, not a 25 kg sack |
A bag printed 25.0kg ± 0.2kg is not a warning sign. It is the more precise declaration. It tells the buyer that the filler's equipment is calibrated and the producer is willing to state the tolerance. A bag with no tolerance stated at all is worth more suspicion than one that states ±0.2 kg.

4. Mercury-free and PVC-FREE markings: what they are actually claiming
Some bags carry a Hg-FREE or PVC-FREE mark. These mean different things and buyers frequently conflate them:
Hg-FREE(无汞): the resin was produced using a mercury-free catalyst in the VCM process. Relevant if a buyer exports to markets with mercury-restriction procurement rules. This is a process claim.PVC-FREEon a PVC bag: reads as contradictory, but on packaging it usually refers to the ink or the bag liner being PVC-free, or to a grade intended for food-contact applications where the additive package avoids certain phthalates. If the mark appears and it matters for the end use, written clarification should be requested.

5. Jumbo bags: the same resin, a different handling decision
At roughly one tonne per bag, jumbo bags (FIBC / 吨袋) are a logistics decision; the resin inside is the same. Whether an order is placed in 25 kg sacks or jumbo bags depends on the unloading and feeding equipment available on site.

The trade-off is straightforward:
| 25 kg sacks | Jumbo bags (~1 t) | |
|---|---|---|
| Handling | Manual, no equipment needed | Requires forklift + lifting frame |
| Unit cost | Higher per tonne (packaging) | Lower per tonne |
| Resin loss | Lower, open one sack at a time | Higher, once opened, the whole tonne is exposed |
| Best for | Small plants, mixed grades, sample orders | High-volume single-grade lines |
6. What a full batch of stock actually looks like
Stock conditions matter more than most buyers expect, because PVC resin is hygroscopic. A bag that has sat in a damp corner will cause problems in the extruder that no COA will predict.

Two things to check on a physical inspection, both visible in this photograph:
- Pallets under everything. Concrete floors transfer moisture. Bags stacked directly on the floor are the most common cause of downstream complaints that the resin felt different.
- No wall contact. A second photograph shows the same principle from the side, stock held clear of the wall, with air able to move.

7. The five-line check
Before a delivery note is signed, these five lines should sit side by side with the purchase order:
- Grade or model: and if it is an S-series model, the equivalent SG range in writing
- Standard number: and whether the COA on file states the same one
- Net weight: nominal or with tolerance; jumbo bags check the tonne figure
- Batch / lot number: must match the COA that was sent
- Additive claims (mercury-free, PVC-free, food-contact) relevant only if the end market requires it
If all five line up, the paperwork and the physical goods agree. If one does not, the question should be raised the same day, before the containers are unstuffed.
A note on where these photographs came from
Every image above is a real bag from stock, photographed as received. The producer markings were deliberately left visible. The point of this article is that the markings are readable by the buyer, on whatever bags arrive, from whichever supplier.
When a buyer needs to know which grade suits an application, the relevant K-value or SG range, end product and quantity can be sent to the supplier, who returns the specific model number and a firm offer.
Each grade has its own page with the GB/T band, the COA items to check and what buyers use it for: SG-3, SG-5, SG-7, SG-8.
The supplier behind those markings, and the checks agreed before dispatch, are listed on the Haoze cooperation page.
SG-5 for the next production run
The grade, the tonnage and the destination port produce a price, a specification sheet and the full document list, usually within 12 hours (GMT+8).
