GMT+8 · Reply within 12 hours
Haoze logo Shandong Haoze Suspension PVC Resin
Get a Quote
ProductUpdated 2026-09-29SG-5

PVC Resin SG-5 (K 66-68, K67) Data Sheet for Pipe

SG-5 is the grade most buyers mean when they write "PVC resin" on an enquiry, and it is also written SG5. The K value band of 66 to 68 is where the trade names K66 and K67 come from, so the same material is quoted to a buyer under three labels. It sits in the middle of the suspension range: enough molecular weight to hold a pressure pipe together, enough flow to run at production speed on a normal twin-screw line. Where the end product is pipe, fittings, window profile or rigid board, SG-5 is almost certainly the grade under consideration.

A 25 kg bag of suspension PVC resin marked SG-5 to GB/T 5761-2018
SG-5 suspension resin: supplied in 25 kg bags, palletised on request
K value66 – 68
Viscosity number107 – 118 mL/g
Average degree of polymerisation981 – 1135
Typical usePipes, fittings, profiles, rigid sheet

Packing|25 kg bags; 800 / 1220 kg jumbo bags; palletised on request|FCL and LCL both work. Palletising and bag printing on request.

Under GB/T 5761-2018, SG-5 is defined by a viscosity number band of 107–118 mL/g, which is the same property expressed as a K value of 66–68 and an average degree of polymerisation of 981–1135. Apparent density for this band is at least 0.48 g/mL, and it governs how the resin feeds and how a bag measures out by volume. The grade is bought for water and drainage pipe, electrical conduit, uPVC profiles, pipe fittings and rigid sheet. The band is wide enough that "SG-5" alone is not a complete specification: the position in the band and the standard edition both belong on the order.

Haoze holds and ships SG-5 as a first-tier distributor working out of Shandong, China. The resin is not polymerised by Haoze. The batch certificate comes from the producing plant, and it is obtained for the buyer on request.

1. What SG-5 actually is

Chinese suspension PVC is graded SG-1 to SG-8. The number marks a viscosity band; it says nothing about quality. SG-5 sits at the general-purpose middle.

Three numbers are quoted for SG-5, and all of them describe the same property, measured or expressed differently:

  • Viscosity number is the direct measurement. The standard defines the band as 107–118 mL/g.
  • K value is the industry shorthand derived from it, quoted here as 66–68. Buyers outside China usually write K67.
  • Average degree of polymerisation is the third expression of the same chain length, 981–1135 for this band.

One property of this band deserves emphasis, because it costs buyers money. A viscosity number of 107 and a viscosity number of 118 are both "SG-5", yet in the extruder the two are different materials. The lower end fuses faster and leaves a wider processing window; the upper end carries more strength and better long-term hydrostatic performance, and asks more of the drive torque and the stabiliser package. A formulation validated on a resin sitting at 112 will still run on a delivery at 107, but the reject rate and the weld strength will not match the validation run.

The enquiry should therefore state the position in the band. "SG-5, viscosity number 112–118" is a specification; "SG-5" on its own is only a category.

2. SG-5 data sheet: K66, K67 and the GB/T figures

Source: GB/T 5761-2018, Table 2. The first three rows define the grade and read the same across all three quality grades. Shipments default to the Superior grade unless the purchase order names another.

Property Superior First Qualified
K value66 – 6866 – 6866 – 68
Viscosity number (mL/g)107 – 118107 – 118107 – 118
Average degree of polymerisation981 – 1135981 – 1135981 – 1135
Impurity particles (per 100 g)≤ 16≤ 30≤ 60
Volatile matter incl. water (%)≤ 0.40≤ 0.40≤ 0.50
Apparent density (g/mL)≥ 0.48≥ 0.45≥ 0.42
Sieve residue, 0.25 mm (%)≤ 1.6≤ 2.0≤ 8.0
Sieve pass, 0.063 mm (%)≥ 97≥ 90≥ 85
Fish eyes (per 400 cm²)≤ 20≤ 30≤ 60
Plasticiser absorption (g per 100 g)≥ 19≥ 17n/a
VCM residue (ppm)≤ 5≤ 5≤ 10
Whiteness, 160 °C / 10 min (%)≥ 78≥ 75≥ 70
Packaging25 kg bags800 / 1220 kg jumbo bagsPalletised, on request

Three notes on how to read this table, because it is the part buyers get wrong most often.

These figures define the SG-5 band under GB/T 5761-2018. Any conforming batch has to sit inside them, and they are the frame the actual lot sits in. What that lot measured is on its certificate, with the test method. The measured value is what incoming inspection checks against the buyer's own acceptance range, and against this table only as context.

Batch COA comes from the producing plant. Each lot carries a certificate issued by the plant that polymerised it. A request at enquiry stage obtains the certificate for the lot actually being offered, sent before the order is placed, so the purchase is not made against a generic sheet. Haoze does not issue certificates and does not present re-typed figures as certificates.

The standard edition cited in the contract matters as well. GB/T 5761-2018 is still in force. The official record shows it was last reviewed on 1 July 2025 with a conclusion of continuing validity. Separately, the standards that govern how vinyl chloride resins are designated and how their properties are tested, GB/T 3402.1-2026 and GB/T 3402.2-2026, were published on 2 July 2026 and take effect on 1 February 2027, replacing the 2005 and 2010 editions. That does not change what SG-5 is, but it changes the test methods written on the certificate. The confirmed facts and the buyer-side checklist are covered in a separate article.

K value and viscosity number

K value is calculated from the viscosity number and is not measured on its own. GB/T 5761-2018 defines the SG-5 band as a viscosity number of 107 to 118 mL/g, which corresponds to K 66 to 68 and an average degree of polymerisation of 981 to 1135. A purchase order that says K67 names a position inside that band, usually the middle. A quotation that gives K67 with no viscosity number gives a range, not a point.

When two certificates are compared, the method matters more than the figures. Viscosity number is measured in a cyclohexanone solution at 25 °C under the method of the standard edition named in the contract. Once GB/T 3402.2-2026 replaces the 2010 edition on 1 February 2027, the method reference on new certificates changes while the band stays as it is. Material from the same reactor can show a small difference in viscosity number across two certificates citing different editions, and the difference sits in the method.

Apparent density

Apparent density states how much resin occupies a given volume of powder, in grams per millilitre. GB/T 5761-2018 sets the floor for SG-5 at 0.48 g/mL for the Superior grade, 0.45 for First and 0.42 for Qualified. The figure is not a purity measure. It reflects particle shape and porosity, which come from the polymerisation route and the drying step.

Two consequences follow. Output comes first: powder at 0.50 g/mL feeds a given screw volume with more kilograms per turn than powder at 0.45, so a line running near its torque limit registers the change in throughput before it registers anything else. Conveying comes second: pneumatic systems and gravity hoppers are sized on bulk density, and a lot at the bottom of the band can starve a line calibrated on material nearer the top.

Bulk density and apparent density are measured by different methods and are not interchangeable. A certificate that reports bulk density in another unit is read against the method stated on it, not against the GB/T apparent density floor.

Volatile matter, sieve residue and fish eyes

Volatile matter including water is capped at 0.40 percent for Superior and First, 0.50 for Qualified. The test is a drying loss, and the effect appears in the extruder: moisture above the cap produces bubbles in the melt and defects on the surface of the finished part. A lot stored through a humid season can fail this line with the polymer unchanged.

Sieve residue on a 0.25 mm sieve is capped at 1.6 percent for Superior, and the pass through 0.063 mm must reach 97 percent. The two figures describe the coarse and the fine end of one distribution. A high coarse residue points to agglomerates that plasticise at a different rate from the rest of the batch. A low fines pass points to a narrow distribution that separates during conveying.

Fish eyes are counted per 400 cm² on a pressed film, with a cap of 20 for Superior. They are the visible trace of unmelted gel particles. On thin-wall and transparent work this line decides acceptance more often than the K value does, because a K value can sit inside the band while the gel count sits outside the limit.

3. Where SG-5 goes, and how it is processed

Process Typical end products Why SG-5 suits it
Extrusion: pipeWater supply and drainage pipe, electrical conduit, irrigation pipeMolecular weight in the middle of the range gives a fusion level that passes pressure and impact testing without pushing torque limits
Extrusion: profileuPVC window and door profiles, wall and ceiling panels, fencing profilesHigher K end of the band holds dimensional tolerance through cooling; the low end gives output
Injection mouldingPipe fittings, valves, shoe components, electrical boxesFlow is adequate for normal wall sections; grades below SG-5 flow better but lose impact strength
CalenderingRigid and semi-rigid sheet, decorative filmFusion behaviour is predictable across the band, which matters on a continuous calender
BlendingDry-blend compounds for downstream processorsFree-flowing powder with density high enough for reliable pneumatic conveying

A practical point that comes up in most first orders: SG-5 is rarely converted on its own. It goes into a formulation with stabiliser, lubricant, filler and, for pipe, impact modifier. A formulation moved onto a new resin source needs lubricant re-tuning even when the K value matches. Particle morphology and porosity differ between plants, and that shows up as a change in fusion time before it shows up as a change on any certificate.

Three symptoms that reach us on a first order, and where they usually point:

  • Fusion uneven along the pipe wall: the lot sits at the low end of the viscosity band, or the

lubricant package was balanced for a higher-K resin.

  • Gels and fish eyes in thin-wall or clear parts: read fish-eye count and sieve residue on the

COA. The K value will not show them.

  • Output below what the line normally runs: apparent density and particle shape. Two lots with

the same K can feed differently.

4. Naming it correctly on a purchase order

What goes on the document What it means Note
SG-5The GB/T 5761-2018 gradeThe designation Haoze quotes and ships under
K 66 – 68 / K67The same band, expressed as K valueMost common form on POs outside China
Viscosity number 107–118 mL/gThe same band, expressed directlyBest form when the contract has an acceptance clause
General purpose / 通用型Trade shorthandNot a specification on its own
SG-5 + K target + standard editionA complete order lineThe recommended form

Two suppliers can quote "SG-5" at the same price and deliver 118 and 108 respectively, with nothing wrong on either document. That is why the position in the band is requested up front. It is the difference between a repeat order and a formulation problem in month two.

5. Packaging, marking and documents

Item Detail Who provides it
Standard packing25 kg PP woven or kraft paper bags with inner linerHaoze
Bulk packing800 kg jumbo bags, or palletised, on requestHaoze
Private labelThe buyer's own bag design for volume ordersHaoze, on request
Batch certificateCertificate of Analysis for the specific lotThe producing plant, obtained by Haoze on request
Trade documentsCommercial invoice, packing list, bill of ladingHaoze and the carrier
Origin and preference documentsCertificate of Origin, Form E and similarIssued on request, lead time applies
Third-party inspectionArranged at loading, buyer-nominated agency welcomeCoordinates with the buyer's inspector

Every bag is marked with grade, batch number, net weight and the plant's identity, so a bag sampled at the buyer's warehouse can be traced back to its certificate. How to read the markings on a PVC resin bag walks through what each field means and which ones belong on the buyer's incoming checklist.

6. What to send for a firm offer

A firm offer for a specific lot, as opposed to a price for a category, is quoted from the following items:

  1. Grade and position in the band: SG-5, plus a viscosity number or K value target.
  2. End product and process: pipe, profile, fitting, sheet; extrusion, injection or calendering.
  3. Line and formulation context: twin-screw or single-screw, the resin currently in use, and whether a source switch is under way.
  4. Quantity: first order and expected monthly volume. FCL and LCL are both workable.
  5. Packaging: 25 kg bags, jumbo bags, palletised, or private label.
  6. Discharge port: the port is specified, with the quote issued FOB Chinese port against it.
  7. Documents required: Certificate of Origin, Form E, third-party inspection at loading.
  8. Payment terms: so the offer states the total cost of the order.

7. Frequently asked

SG-5 and K67: the same band in two notations In practice yes. SG-5 is the Chinese grade designation and K67 is the same molecular weight band expressed as a K value. For contractual purposes it is worth writing both, plus the viscosity number band, so there is no room to argue about where in the band a delivery sits.

COA review before the order is placed The quantity under consideration is stated, and the certificate for the lot being offered is obtained from the producing plant and sent for review. If the measured values do not sit inside the buyer's acceptance range, nothing has been spent.

SG-5 versus SG-7 for pipe SG-5 is the standard choice for pressure pipe and profiles. SG-7 and SG-8 are lower viscosity grades bought for rigid sheet, bottles, transparent work and high-flow injection. The full grade comparison is here.

Jumbo bags and private-label printing Both are possible. 800 kg jumbo bags and palletised loading are arranged on request; private-label bag printing is available for volume orders. The artwork, once received, is confirmed against the quantity.

What the price depends on The feedstock route the lot came from, the volume and packaging, the delivery basis and the payment terms, and (more than anything else on a PVC order) the timing of the purchase. Quotes are held for a shorter window than on most plastics, because the feedstock side moves faster. The parameters above produce a dated offer.

What is the apparent density of SG-5 Apparent density for the SG-5 band is at least 0.48 g/mL for the Superior grade and at least 0.45 g/mL for the First grade under GB/T 5761-2018. It is a floor, not a fixed figure: the value governs how the powder feeds and how a bag measures out by volume, and two conforming lots can sit at different points above it.

Whether a data sheet can be issued before the order The specification range is the GB/T 5761-2018 table above, and any conforming SG-5 lot sits inside it. Measured values belong to the batch: the certificate for the lot being offered is obtained from the producing plant and sent for review before the order is placed. Haoze does not re-type figures into a data sheet of its own.

Minimum order and how dispatch is arranged FCL and LCL are both workable, and the first order is quoted on the quantity actually under consideration. Dispatch is arranged in about 5 days from confirmation. Packaging is confirmed at the same time: 25 kg bags, jumbo bags or palletised loading.

Trade and payment terms Offers are issued FOB Chinese port, against the discharge port the buyer names. Payment is by T/T. Other delivery bases and payment instruments are not quoted on this page; where a buyer's process requires something else, it is raised at enquiry stage, not assumed.

Where a specification names an international grade, the K value or the viscosity band identifies the compatible Chinese grade in this range.

Get a firm offer for this grade

The end product, the position in the band, the quantity and the discharge port produce a dated offer together with the COA for the lot being offered.

Related grades

Same suspension process, different K-value bands. Pick by end product, then compare the tables side by side.

WhatsApp