PVC Resin Products: SG-5, SG-3, SG-7, SG-8
Four standard suspension grades are held and shipped out of Shandong, China. Between them they cover almost every enquiry Haoze receives: pipe and profile at the top of the volume, soft plasticised products at the other end, and the low-viscosity grades for sheet, bottle and thin-wall work. 25 kg bags, jumbo bags or palletised; FCL and LCL.
The pages below carry the selection logic, the full requirement figures for all four grades, and the boundary between what Haoze stands behind and what it declines to claim.
PVC Resin SG-3
SG-3 suspension PVC resin, K 71-72, viscosity 127-135 mL/g. The GB/T 5761-2018 data sheet, what the numbers mean, and what to send for a firm offer.
PVC Resin SG-5
SG-5 suspension PVC resin, K 66-68, viscosity 107-118 mL/g. The GB/T 5761-2018 data sheet for pipe and profile grades, plus what to send for a firm offer.
PVC Resin SG-7
SG-7 suspension PVC resin, K 60-62, viscosity 87-95 mL/g. The GB/T 5761-2018 data sheet, what each figure decides, and what to send for a firm offer.
PVC Resin SG-8
SG-8 suspension PVC resin, K 55-59, viscosity 73-86 mL/g. The GB/T 5761-2018 data sheet, what each figure decides, and what to send for a firm offer.
1. Which grade fits the product
Grade selection is almost never ambiguous once the end product and the process are known. The K value follows from those two.
| End product | Process | Grade | Why |
|---|---|---|---|
| Water and drainage pipe, conduit, irrigation pipe | Extrusion | SG-5 | Molecular weight in the middle: fuses well enough to pass pressure and impact tests, flows well enough for output |
| uPVC window and door profiles, panels, fencing | Extrusion | SG-5 | Holds dimensional tolerance through cooling without demanding an unworkable torque |
| Pipe fittings, valves, electrical boxes | Injection | SG-5, or SG-7 on thin walls | SG-5 covers normal wall sections; thin and long-flow parts need the lower viscosity |
| Cable insulation and sheathing | Extrusion | SG-3 | The highest plasticiser absorption in the range, built for a heavily plasticised formulation |
| Flexible film, artificial leather, hose, footwear | Calendering, extrusion, moulding | SG-3 | Flexibility and low-temperature performance in the finished article |
| Rigid and transparent sheet, calendered film | Calendering, extrusion | SG-7, or SG-8 for the thinnest and clearest | Low melt viscosity gives clean roll release and even die filling |
| Bottles, containers, packaging | Blow moulding, thermoforming | SG-7 | Fills thin walls at low pressure and at a lower melt temperature |
| Foam board, shrink film, thin-wall transparent parts | Foam extrusion, injection, film | SG-8 | The furthest flow and the lowest gel level of the four |
A product that is not on this list can still be matched: the end product and the process, once stated, produce a recommendation among the four, including the answer that none of them is right.
2. The four grades, side by side
| Property | SG-3 | SG-5 | SG-7 | SG-8 |
|---|---|---|---|---|
| K value | 71 – 72 | 66 – 68 | 60 – 62 | 55 – 59 |
| Viscosity number (mL/g) | 127 – 135 | 107 – 118 | 87 – 95 | 73 – 86 |
| Average degree of polymerisation | 1251 – 1370 | 981 – 1135 | 741 – 845 | 650 – 740 |
| Apparent density (g/mL) | ≥ 0.45 | ≥ 0.48 | ≥ 0.52 | ≥ 0.52 |
| Plasticiser absorption (g per 100 g) | ≥ 26 | ≥ 19 | ≥ 12 | ≥ 12 |
| Fish eyes (per 400 cm²) | ≤ 20 | ≤ 20 | ≤ 30 | ≤ 30 |
| Volatile matter incl. water (%) | ≤ 0.30 | ≤ 0.40 | ≤ 0.40 | ≤ 0.40 |
| Typical application | Cable, film, artificial leather, hose | Pipes, fittings, profiles, rigid sheet | Rigid sheet, bottles, calendered film, injection | Transparent sheet, foam board, pipe fittings, injection |
What matters is the relationship between the numbers. As the K value falls from SG-3 to SG-8, viscosity number and polymerisation fall with it, and apparent density rises. That is the whole design of the system: higher molecular weight buys strength and plasticiser capacity, lower molecular weight buys flow and packing density.
The other thing worth noticing is how wide the bands are. SG-5 spans a viscosity number of 107 to 118, and SG-8 spans 73 to 86. Two deliveries can both be "SG-5" and behave differently in the same extruder. This is why the position in the band is requested on every enquiry, and why a quote that names only a grade leaves a specification open that later becomes somebody's reject rate.
3. What these figures are, and what they are not
They are the band requirements from GB/T 5761-2018. They define the range a conforming batch has to sit inside. What a specific delivery measured is on that delivery's certificate.
The batch certificate comes from the producing plant. Haoze is a first-tier distributor, not the plant that polymerises the resin. Each lot has a certificate issued by the plant's laboratory. A request at enquiry stage obtains the certificate for the lot actually being offered, sent before the order is placed, so the decision is made against a measured figure rather than a marketing table.
Certificates are not re-typed and presented as Haoze's own. Where the COA for a lot on the water is needed before the balance payment is released, that is a normal request and it is honoured.
The standard edition on the contract matters too. GB/T 5761-2018 remains in force; the official record shows it was reviewed on 1 July 2025 and continued. The standards that govern designation and test methods, GB/T 3402.1-2026 and GB/T 3402.2-2026, take effect on 1 February 2027 in place of the 2005 and 2010 editions. The confirmed facts and the buyer-side checklist are covered in a separate article.
4. Grades beyond these four
SG-5, SG-3, SG-7 and SG-8 are the standing grades, and they account for nearly every order shipped. They are not the limit of what can be sourced.
Other suspension grades (SG-4, SG-2, SG-1 and SG-6) can be sourced through the same channel. Paste resin (emulsion and micro-suspension) is available on request. Grade and application, once stated, are checked against availability before a quote is issued, rather than a lot being promised that has not been located.
Channels for CPVC, PE, PP and HDPE also exist and can be included in the same enquiry. That side is smaller for Haoze, and it is stated up front.
5. How to enquire
Every enquiry that turns into a clean order contains the same six things:
- The grade, and the position in the band: not "SG-5" but "SG-5, viscosity number 112–118".
- The end product and the process: what is made and how.
- The quantity: first order and expected monthly volume.
- The packaging: 25 kg bags, jumbo bags, palletised, or the buyer's own bag design.
- The discharge port: the port is specified, and the quote is issued FOB Chinese port against it.
- The documents and the payment terms: so the figure in the offer is the cost of the order.
How to read the markings on a PVC resin bag is worth ten minutes before the first delivery arrives, and the grade comparison article is worth reading while two grades are still under consideration.
Get a firm offer for this grade
The end product, the position in the band, the quantity and the discharge port produce a dated offer together with the COA for the lot being offered.
