PVC Resin SG-7 (K 60-62) Data Sheet for Rigid Sheet
SG-7 is where PVC starts flowing properly. The molecular weight is low enough that the melt fills a thin section and releases from a hot calender roll cleanly, and the apparent density is high enough that every screw turn delivers useful output. Rigid sheet, calendered film, bottles and thin-wall injection parts are the applications worth testing it for.

Packing|25 kg bags; 800 / 1220 kg jumbo bags; palletised on request|FCL and LCL both work. Palletising and bag printing on request.
Under GB/T 5761-2018, SG-7 is defined by a viscosity number band of 87–95 mL/g, which is the same property expressed as a K value of 60–62 and an average degree of polymerisation of 741–845. Its characteristic figures are a higher apparent density requirement, at least 0.52 g/mL, and a low plasticiser absorption requirement of at least 12 g per 100 g. The grade is bought for rigid sheet, bottles and containers, calendered film and high-flow injection moulding.
Haoze ships SG-7 as a first-tier distributor out of Shandong, China. The resin is not polymerised by Haoze. The batch certificate is issued by the producing plant and is obtained for the buyer on request.
1. What SG-7 actually is
SG-7 sits below SG-5 on the molecular weight ladder. The band, in three expressions:
- Viscosity number: the standard defines SG-7 as 87–95 mL/g.
- K value: 60–62. Buyers outside China usually write K61 or K60.
- Average degree of polymerisation: 741–845.
Two consequences follow from the lower molecular weight, and both are the reason buyers choose this grade in place of SG-5.
It flows. Melt viscosity is lower, so the material fills thin and intricate sections (a bottle wall, a thin calendered film, a complex injection part) at lower melt temperature and lower injection pressure. On a calender, lower viscosity also means cleaner release from the roll and a better surface, which is why transparent and glossy rigid film is usually not made on a high-K grade.
It packs. SG-7 carries a higher apparent density requirement (at least 0.52 g/mL, against at least 0.48 for SG-5) and a finer particle size distribution. In practice that means more kilograms per screw turn and better feeding stability, which shows up as output before it shows up on any certificate.
The cost is toughness. Lower molecular weight means lower impact strength and lower resistance to creep under load. Rigid sheet made on SG-7 alone will crack before a sheet made on SG-5 will. This is not a defect of the grade. It is why rigid formulations on SG-7 normally carry an impact modifier and a processing aid, and why the formulation work matters more on this grade than on SG-5. The plasticiser absorption requirement, at least 12 g per 100 g, reflects the same thing from the other side: this is a rigid-product grade and it is not built to take a heavy plasticiser load.
2. Specification
Source: GB/T 5761-2018, Table 2. The first three rows define the grade and read the same across all three quality grades. Shipments default to the Superior grade unless the purchase order names another.
| Property | Superior | First | Qualified |
|---|---|---|---|
| K value | 60 – 62 | 60 – 62 | 60 – 62 |
| Viscosity number (mL/g) | 87 – 95 | 87 – 95 | 87 – 95 |
| Average degree of polymerisation | 741 – 845 | 741 – 845 | 741 – 845 |
| Impurity particles (per 100 g) | ≤ 20 | ≤ 40 | ≤ 100 |
| Volatile matter incl. water (%) | ≤ 0.40 | ≤ 0.40 | ≤ 0.50 |
| Apparent density (g/mL) | ≥ 0.52 | ≥ 0.45 | ≥ 0.40 |
| Sieve residue, 0.25 mm (%) | ≤ 1.6 | ≤ 2.0 | ≤ 8.0 |
| Sieve pass, 0.063 mm (%) | ≥ 97 | ≥ 90 | ≥ 80 |
| Fish eyes (per 400 cm²) | ≤ 30 | ≤ 50 | n/a |
| Plasticiser absorption (g per 100 g) | ≥ 12 | ≥ 14 | n/a |
| VCM residue (ppm) | ≤ 5 | ≤ 10 | n/a |
| Whiteness, 160 °C / 10 min (%) | ≥ 75 | n/a | n/a |
| Packaging | 25 kg bags | 800 / 1220 kg jumbo bags | Palletised, on request |
Three notes on reading this table.
Two limits are looser than on SG-5. Impurity particles go from ≤ 16 to ≤ 20 per 100 g, fish eyes from ≤ 20 to ≤ 30 per 400 cm², and whiteness from ≥ 75 % to the same ≥ 75 %. For a pigmented or filled rigid product this is not a problem. For a transparent sheet or a clear bottle, fish eyes and impurity particles are exactly the defects a customer will see, so where clarity is the requirement, tighter acceptance figures belong in the order line.
These are the SG-7 band requirements. A conforming batch has to sit inside them, and the lot's own measured values are on its certificate. Incoming inspection compares against the buyer's own acceptance range.
Batch COA comes from the producing plant. A request at enquiry stage obtains the certificate for the lot being offered, sent before the order is placed. Haoze does not issue certificates.
Standards note: GB/T 5761-2018 remains in force. The official record shows it was reviewed on 1 July 2025 with a conclusion of continuing validity. GB/T 3402.1-2026 and GB/T 3402.2-2026, which govern designation and test methods, take effect on 1 February 2027 in place of the 2005 and 2010 editions. The buyer-side checklist is covered in a separate article.
K 60–62: the flow end of the range
SG-7 sits at the low molecular weight end of the suspension range. GB/T 5761-2018 defines it as a viscosity number of 87 to 95 mL/g, K 60 to 62, average degree of polymerisation 741 to 845. The band is roughly one K step below SG-5, and that step shows up in the melt: lower viscosity, easier filling of thin sections, shorter residence time in the die.
The trade-off is mechanical. Lower molecular weight means lower melt strength and lower impact resistance in the finished part. A pipe compound built on K66 does not transfer to K60 without reformulation, and a fitting moulded from K60 gets its impact from the formulation, not from the resin. Lines that move from SG-5 to SG-7 for cycle time usually keep both grades in parallel and switch after the formulation has been rebalanced.
Apparent density and what it does to output
For SG-7 the GB/T floor for apparent density is 0.52 g/mL at Superior grade, against 0.48 for SG-5. The higher floor fits the application: rigid sheet, calendered film and thin-wall moulding are output-sensitive processes, and denser powder feeds a screw with more kilograms per turn.
Reading the figure against a certificate requires one caution. Apparent density is measured on the powder as delivered, and a lot that has settled in a jumbo bag in transit can read differently from the same lot sampled at the silo. Incoming acceptance is best taken from a sample drawn after the contents have been homogenised, using the method named on the certificate.
Supplier changes are worth watching on this figure as well. Two plants can both certify 0.52 g/mL and still feed differently, because particle shape varies while the density value matches.
Plasticiser absorption, volatiles and fish eyes
Plasticiser absorption for SG-7 is set at 12 g per 100 g for Superior and 14 for First. The lower figure, against 19 for SG-5, follows from the higher apparent density and lower porosity of the particle: there is less internal surface for the plasticiser to enter. In rigid compounds this is an advantage, since plasticiser uptake is not wanted; in flexible ones it is a limitation, and SG-3 or SG-5 takes that work.
Volatile matter is capped at 0.40 percent for Superior and First, 0.50 for Qualified. Sieve residue at 0.25 mm is capped at 1.6 percent for Superior, with 97 percent or more passing 0.063 mm. Fish eyes are capped at 30 per 400 cm², a looser limit than the 20 set for SG-5, which matters on clear sheet and bottles where the defect is visible to the end user.
3. Where SG-7 goes, and how it is processed
| Process | Typical end products | Why SG-7 suits it |
|---|---|---|
| Calendering | Rigid and transparent film, sheet, laminating film | Low melt viscosity gives clean roll release and surface gloss |
| Extrusion: sheet | Rigid sheet and board, foam board | Higher apparent density supports output; flow aids die filling on thin sheet |
| Blow moulding and thermoforming | Bottles, containers, packaging | Fills thin walls at low pressure and at a lower melt temperature |
| Injection moulding | Thin-wall parts, fittings, profiles, technical parts | Flow length is the limiting factor on thin sections, and SG-7 has it |
| Compounds | Rigid dry blends for downstream processing | Consistent particle distribution feeds and conveys well |
The formulation point again, because it decides whether SG-7 works on a given line: on this grade the purchase is flow, bought against impact strength. The impact modifier and the processing aid belong in the costing before a line switches over, or the sheet will come out beautiful and brittle.
4. Naming it correctly on a purchase order
| What goes on the document | What it means | Note |
|---|---|---|
| SG-7 | The GB/T 5761-2018 grade | The designation Haoze quotes and ships under |
| K 60 – 62 / K61 | The same band, expressed as K value | Common on POs outside China |
| Viscosity number 87–95 mL/g | The same band, expressed directly | Best form when the contract has an acceptance clause |
| High flow grade / 高流动 | Trade shorthand | Not a specification on its own |
| SG-7 + fish eye limit + standard edition | A complete order line for transparent work | The recommended form where clarity matters |
Where the output is clear or glossy, the order line needs one field a pigmented-product buyer does not: a tight fish eye and impurity particle limit. The standard limit is not a clarity specification.
5. Packaging, marking and documents
| Item | Detail | Who provides it |
|---|---|---|
| Standard packing | 25 kg PP woven or kraft paper bags with inner liner | Haoze |
| Bulk packing | 800 kg jumbo bags, or palletised, on request | Haoze |
| Private label | The buyer's own bag design for volume orders | Haoze, on request |
| Batch certificate | Certificate of Analysis for the specific lot | The producing plant, obtained by Haoze on request |
| Trade documents | Commercial invoice, packing list, bill of lading | Haoze and the carrier |
| Origin and preference documents | Certificate of Origin, Form E and similar | Issued on request, lead time applies |
| Third-party inspection | Arranged at loading, buyer-nominated agency welcome | Coordinates with the buyer's inspector |
How to read the markings on a PVC resin bag covers batch number, grade marking and the fields that belong on the buyer's incoming checklist.
6. What to send for a firm offer
A firm offer for a specific lot is quoted from the following items:
- Grade and position in the band: SG-7, plus a viscosity number or K value target.
- End product and process: sheet, film, bottle or injection part; calendering, extrusion, blow moulding or injection.
- Clarity requirement: pigmented, translucent or optically clear. This decides which limits go on the order line.
- Formulation context: whether an impact modifier and processing aid are in use, and what the line is switching from.
- Quantity: first order and expected monthly volume. FCL and LCL are both workable.
- Packaging: 25 kg bags, jumbo bags, palletised, or private label.
- Discharge port: the port is specified, with the quote issued FOB Chinese port against it.
- Documents required: Certificate of Origin, Form E, third-party inspection at loading.
- Payment terms: so the offer states the total cost of the order.
7. Frequently asked
SG-7 or SG-8 for rigid sheet Both are low-viscosity grades and both are used in rigid sheet. SG-7 sits at K 60–62, SG-8 at K 55–59. SG-8 flows further and is the usual choice for foam board and thin transparent sheet; SG-7 holds a little more toughness, which matters on thicker sections. With the sheet thickness and the process stated, Haoze recommends which of the two to ship.
Why the fish eye limit is looser than on SG-5 The standard treats SG-7 and SG-8 as grades aimed at pigmented and filled rigid products, where a fish eye does not show. On clear material the standard limit is not the number to accept. The buyer sets its own figure and puts it in the contract.
COA review before the order is placed The quantity under consideration is stated, and the certificate for the lot being offered is obtained from the producing plant and sent for review. If the apparent density or viscosity number does not sit inside the buyer's acceptance range, nothing has been spent.
Jumbo bags and private-label printing Both are possible. 800 kg jumbo bags and palletised loading on request; private-label bag printing for volume orders.
What the price depends on The feedstock route the lot came from, volume and packaging, delivery basis, payment terms, and timing. PVC quotes hold for a shorter window than most plastics.
Where a specification names an international grade, the K value or the viscosity band identifies the compatible Chinese grade in this range.
Get a firm offer for this grade
The end product, the position in the band, the quantity and the discharge port produce a dated offer together with the COA for the lot being offered.
Related grades
Same suspension process, different K-value bands. Pick by end product, then compare the tables side by side.
